Railway relays

  • TTBCR 200 relay – Delay on drop-out, instantaneous

    The TTBCR 200 time delay relay has 2 changeover simple break contacts with 1 instantaneous contacts and 1 delayed contacts on drop-out fully programmable (with dipswitch) from 0.5 seconds to 4 seconds. The access to dip switch is available by removing time delay cover. This feature prohibits frivolous field time delay setting. The plug-in design offers secure locking feature for maximum ease of maintenance (no wires need to be disconnected…
  • TTBCR 400 relay – Delay on drop out instantaneous

    The TTBCR 400 time delay relay has 4 changeover simple break contacts with 2 instantaneous contacts and 2 delayed contacts on drop-out fully programmable (with dipswitch) from 0.5 to 4 seconds. The access to dip switch is available by removing time delay cover. This feature prohibits frivolous field time delay setting. The plug-in design offers secure locking feature for maximum ease of maintenance (no wires need to be disconnected or…
  • UB 003 relay – 3 Level load shedding

    The voltage monitoring relay UB 003 opens auxiliary loads circuits when battery voltage becomes too low and puts them back in service when battery voltage recovers. A time delay of 20 seconds engages before opening a load circuit and a time delay of 2 seconds before putting back in service a load. The plug-in design offers secure locking feature for maximum ease of maintenance (no wires need to be disconnected…
  • UB 200 relay – Voltage monitoring

    The voltage monitoring relay UB 200 opens auxiliary loads circuits when battery voltage becomes too low and puts them back in service when battery voltage recovers. A time delay of several seconds (to be defined) engages before opening a load circuit and a time delay of several seconds (to be defined) before putting back in service a load. The plug-in design offers secure locking feature for maximum ease of maintenance…
  • UB A400 relay – Voltage monitoring

    The voltage monitoring relay UB A400 opens auxiliary loads circuits when battery voltage becomes too low and puts them back in service when battery voltage recovers. A time delay of 20 seconds engages before opening a load circuit and a time delay of 2 seconds before putting back in service a load. The plug-in design offers secure locking feature for maximum ease of maintenance (no wires need to be disconnected…
  • UB C200 relay – Voltage monitoring

    The voltage monitoring relay UB C200 opens auxiliary loads circuits when battery voltage becomes too low and puts them back in service when battery voltage recovers. A time delay of several seconds (to be defined) engages before opening a load circuit and a time delay of several seconds (to be defined) before putting back in service a load. The plug-in design offers secure locking feature for maximum ease of maintenance…
  • UMD-U200 relay – Voltage monitoring

    This product is no longer available. The replacement relay is the MTDV4-U200. Plug-in electronic voltage monitoring relay with one change-over contact and one normally open contact. The pull-in voltage is adjustable with a lockable knob. The relay can also be supplied with a fixed pull-in voltage (no knob). The UMD-U200 offers a very small hysteresis (difference between pull-in and drop-out voltage) and does not need an auxiliary supply. The relay…
  • UMD-U300 relay – Voltage monitoring, AC input

    Plug-in electronic voltage monitoring relay with one change-over contact and one normally open contact, suitable for AC voltages with a frequency of 50/60 Hz. The pull-in voltage is adjustable with a lockable knob. The relay can also be supplied with a fixed pull-in voltage (no knob). The UMD-U300 offers a very small hysteresis (difference between pull-in and drop-out voltage) and does not need an auxiliary supply. The relay is equipped…
  • UTC relay – Voltage monitoring & off delay

    The time delay relay UTC incorporates also a voltage control function. The time delay is initiated by an impulse on the relay command which also closes the contact. The time delay relay can be initiated if the input voltage d0 is higher than the voltage control threshold. If the input voltage d0 is lower than the voltage control threshold, then the time delay is reset to 0, the contact is…
  • V10 socket – Screw terminal, wall mount

    This product is no longer available. The replacement socket is the V16. The V10 is a surface / wall mount relay socket. The V10 socket has one screw terminal per relay contact suitable for two wires up to 2.5 mm2, so looping/daisy chaining can be done on the socket and no external connector or terminal is needed. Optional 35 mm rail mount with A109 rail clip. To prevent fault relay…
  • V11 socket – Screw terminal, wall mount, protection diode

    This product is no longer available. The replacement socket is the V16. The V11 is a surface / wall mount relay socket. The V11 socket has one screw terminal per relay contact suitable for two wires up to 2.5 mm2, so looping/daisy chaining can be done on the socket and no external connector or terminal is needed. Optional 35 mm rail mount with A109 rail clip. The V11 has a…
  • V12 socket – Screw terminal, wall mount, 4 kV insulation

    This product is no longer available. The replacement socket is the V16. The V12 is a surface / wall mount relay socket. The V12 socket has one screw terminal per relay contact suitable for two wires up to 2.5 mm2, so looping/daisy chaining can be done on the socket and no external connector or terminal is needed. Optional 35 mm rail mount with A109 rail clip. The V12 has 4…
  • V13 socket – Screw terminal, wall mount, diode and LED

    This product is no longer available. The replacement socket is the V16. The V13 is a surface / wall mount relay socket. The V13 socket has one screw terminal per relay contact suitable for two wires up to 2.5 mm2, so looping/daisy chaining can be done on the socket and no external connector or terminal is needed. Optional 35 mm rail mount with A109 rail clip. The V13 has a back…
  • V14 socket – PCB mount

    This product is no longer available. The replacement socket is the V18. The V14 is a relay socket for soldering on PCB. The relay will be plugged into the socket, the socket will be soldered on the PCB. There is only one way of connecting the relay to the socket to guarantee correct placement of the relay. Application The V14 relay socket is suitable for general railway applications with a…
  • V15 socket – Screw terminal, wall mount, diode and LED

    This product is no longer available. The replacement socket is the V16. The V15 is a surface / wall mount relay socket. The V15 socket has one screw terminal per relay contact suitable for two wires up to 2.5 mm2, so looping/daisy chaining can be done on the socket and no external connector or terminal is needed. Optional 35 mm rail mount with A109 rail clip. The V15 has a back…
  • V16 socket Screw terminal, wall rail mount

    The V16 is a surface / wall and 35 mm rail mount relay socket. The V16 socket is suitable for two stripped wires up to 3.3 mm2, so looping/daisy chaining can be done on the socket and no external connector or terminal is needed. Equipped with an integrated retaining clip. To prevent fault relay placement the socket can be equipped with mechanical keying to accept only designated identical keyed relays.…