Rolling stock

• 

  Corner shaped busbar CR-Series, 6 poles

  Ordering code: 631311106
• 

  Corner shaped busbar CR-Series, 7 poles

  Ordering code: 631311107
• 

  Corner shaped busbar CR-Series, 8 poles

  Ordering code: 631311108
• 

  Corner shaped busbar CR-Series, 9 poles

  Ordering code: 631311109
• 

  CR-Series Railway hydraulic magnetic circuit breaker

  Under normal operating conditions, accidents may not appear to be a problem. However, normal operating conditions are not always guaranteed. Under strained or heavy use, a motor and/or another load-generating component within the equipment will draw additional current from the power source; when this happens, the equipment’s wires and/or components will overheat and may ultimately burn up. In addition to protecting the equipment, the entire electrical system including the control…
• 

  CTD4-U200N relay – customizable timer, 4 pole

  Plug-in electronic railway customizable timer relay with four change-over contacts. Fully customizable according customer’s requirements concerning timing diagram and delay type. Almost any timing diagram is possible: for example time delays with delay on pull-in, on drop-out or both, symmetrical or asymmetrical flashing, 1-shot, 2-shot, 3-shot etc. or a combination of all these. Delay/pulse times are adjustable with 1 or 2 lockable knobs. The relay can also be supplied with…
• 

  CU/CP-U200-B relay – High contact life

  Miniature railway relay with two change-over contacts. Equiped with magnetic arc blow-out for higher contact life. The contacts are weld-no-transfer contacts: they are mechanically forced in the same position. Relay for plug-in mounting (CU version) or for PCB mounting (CP version). The construction of the relay and choice of materials makes the CU/CP-U200-B relay suitable to withstand corrosive atmospheres, low and high temperatures, shock & vibrating and dry to very…
• 

  CU/CP-U200-D relay – Miniature, large pull-in voltage range

  Miniature railway relay with one change-over contact and one normally-open contact. Very sensitive relay with a large pull-in voltage range: 40 %...125 % of the nominal voltage. The contacts are weld-no-transfer contacts: they are mechanically forced in the same position. Standard with high insulation because of flash barrier. Relay for plug-in mounting (CU version) or PCB mounting (CP version). The construction of the relay and choice of materials makes the…
• 

  CU/CP-U200-G relay – Miniature, 2 pole

  Miniature railway relay with two change-over contacts. The contacts are weld-no-transfer contacts: they are mechanically forced in the same position. Standard with high insulation because of flash barrier. Relay for plug-in mounting (CU version) or for PCB mounting (CP version). The construction of the relay and choice of materials makes the CU/CP-U200-G relay suitable to withstand corrosive atmospheres, low and high temperatures, shock & vibrating and dry to very humid…
• 

  CU/CP-U200-U relay – High contact life

  Miniature railway relay with one double make, double break contact. High maximum contact current and long electrical life. Relay for plug-in mounting (CU version) or for PCB mounting (CP version). The construction of the relay and choice of materials makes the CU/CP-U200-U relay suitable to withstand corrosive atmospheres, low and high temperatures, shock & vibrating and dry to very humid environments. With a very compact design and a wide range…
• 

  CU/CP-U300-G relay – Miniature, AC coil

  Miniature railway relay with two change-over contacts suitable for AC coil voltages with a frequency of 50/60 Hz. The contacts are weld-no-transfer contacts: they are mechanically forced in the same position. Standard with high insulation because of flash barrier. Relay for plug-in mounting (CU version) or for PCB mounting (CP version). The construction of the relay and choice of materials makes the CU/CP-U300-G relay suitable to withstand corrosive atmospheres, low…
• 

  CU/CP-U300-U relay – Miniature, AC coil

  Miniature railway relay with one double make, double break contact suitable for AC coil voltages with a frequency of 50/60 Hz. High maximum contact current and long electrical life. Relay for plug-in mounting (CU version) or for PCB mounting (CP version). The construction of the relay and choice of materials makes the CU/CP-U300-U relay suitable to withstand corrosive atmospheres, low and high temperatures, shock & vibrating and dry to very…
• 

  CU/CP-U900-D relay – Current monitoring

  Miniature current monitoring railway relay with one change-over and one normally open contact. Suitable for AC currents. The contacts are weld-no-transfer contacts: they are mechanically forced in the same position. Very sensitive and high insulation between coil and contact. Relay for plug-in mounting (CU version) or for PCB mounting (CP version). The construction of the relay and choice of materials makes the CU/CP-U900-D relay suitable to withstand corrosive atmospheres, low…
• 

  CU/CP-U900-I relay – Current monitoring

  Miniature current monitoring railway relay with one change-over contact. Suitable for AC or DC currents. Very sensitive and high insulation between coil and contact. Relay for plug-in mounting (CU version) or for PCB mounting (CP version). The construction of the relay and choice of materials makes the CU/CP-U900-I relay suitable to withstand corrosive atmospheres, low and high temperatures, shock & vibrating and dry to very humid environments. With a very…
• 

  D-Dock

  The D-dock system consists of a D-dock Test Block which is put between the existing relay socket and the existing D-U plug-in relay. All 14 relay-pins are wired to the Break-Out Box enabling to connect measuring equipment like multimeters, scope meters or data analyzers to log operations during longer period. This makes fault finding easy. The D-dock fits in tightly packed relay panels and small cabinets.  It can operate unattended…
• 

  D-Test Switch

  Plug-in test switch with 4 change-over contacts to simulate D-relay operation in an electrical installation. With latchable manual operation and voltage presence indicator. D-relay housing and contact configuration to be suitable for all D-relay sockets. Application Testing and commissioning electrical installations. Can be used for maintenance purposes and fault finding. Features Manual operated relay (no coil installed) Latchable manual switch Instantaneous, 4 C/O contacts Voltage presence indicator Magnetic arc blow-out…